Produse pentru neti pot solution (3)

Sanafarbe P: Vopsea non-toxică respirabilă pe bază de var, pentru interior și exterior

Sanafarbe P: Vopsea non-toxică respirabilă pe bază de var, pentru interior și exterior

Sanafarbe P Breathable, natural, non-toxic paint, for internal and external surfaces, diffusive type, based on lime putty. Mineral-based, active formulation, high natural anti-mildew and anti-condensation capacity, prepared according to the traditional recipes, for use in ecological building interventions and in the restoration of vintage buildings and monuments. Product based on lime putty and natural pigments. Sanafarbe P has a high breathability, remarkable mildewcide and antibacterial properties. It has no solvents, thinners, harmful substances in general. Decorative and internal and external restoration paint. The application supports will be free from fouling, powder, non-adhering parts, etc.; existing paints (washable, organic, solvent based etc.) must be removed. A preliminary fixative treatment of the surfaces is always advisable with a consolidating, transparent, Sanaxil Fix primer, based on potassium silicate. The application of Sanaxil Fix can be done by brush, roller or spray: the number of hands required and the dilution ratio with the most suitable water must be determined according to the conditions and absorption degradation of the supports. The admissible dilution range provides for water addition up to a maximum of 1:1 ratio. Apply by brush, roller, spray, in two coats, spaced-apart, one from the other, by about 24 hours. It allows the easy reproduction of traditional finish type: sponging, rubbing, marbling, infilling. Sanafarbe P is dry to the touch after 2 hours, it can be overcoated after 4 hours, while it will be dry in-depth after 8-16 hours. Apply from 0.20 to 0.40 liters of Sanafarbe P per square metre of surface to be painted. Pail 4 l - Pail 14 l
Film Izolant pentru Feronerie

Film Izolant pentru Feronerie

Le film isolant thermique LOW E 3M CC75 est issue d’une technologie récente et innovante. Celle-ci consiste à assembler plusieurs couches de métaux précieux, spécifiquement choisis pour agir sur certaines ondes du spectre solaire (IR, UV, etc.) En été, le film solaire réfléchit la chaleur, avec un minimum d’effet miroir ; En hiver, il réduit fortement les pertes de chaleur et garantit des économies d’énergie.
Syntech Poliurea Top Coating: Strat de protecție pe bază de rășină poliuretanică alifatică

Syntech Poliurea Top Coating: Strat de protecție pe bază de rășină poliuretanică alifatică

Syntech Poliurea Top Coating A protective, pigmented, two-component formulation based on aliphatic polyurethane resins, ideal as a protective and aesthetic coating on waterproofing with SYNTECH POLIUREA SPRAY. Characterised by high levels of elasticity and elevated protection, even in aggressive atmospheres. Available on request in shades from the RAL colour range. Surface coating pigmented for colouring polyurethane claddings, and their protection from UV rays (which in the absence of the top coating would alter the colour over time). After suitable priming with SYNTECH POLYUREA PRIMER, it can also be applied as a simple coloured aliphatic protective coating. Polyurea support Vacuum and blow the surfaces to eliminate any dust that may have accumulated in the 24-48 hours following the installation of SYNTECH POLIUREA SPRAY Support in concrete, mortar, brick, tiles The support on which the polyurea system must be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. The humidity of the support must be <= 3%. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. In case of presence (even suspected) of humidity deriving from capillary rising from the substrate, it is recommended to apply in advance the epoxy resin for "wet substrates" Syntech Pavidamp. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. It is recommended to use Primer from the SYNTECH POLIUREA PRIMER range. On particularly absorbent substrates, to avoid the formation of craters / blowholes on the surface of the freshly sprayed product, it is recommended to use primers from the SYNTECH POLIUREA PRIMER range, always contacting the Azichem technical staff for clarification on the most suitable type to use. Apply several layers of primer until the porosity is saturated and providing a light dusting with clean and dry quartz sand (0.4-0.7 mm). Never dust off the primer. Provide suitable elastic sealing systems to cover joints, fittings, cracks or fissures subject to significant movements. Pour component B with component A into a single container, taking care to remove all the material from the packaging. Mix thoroughly with a mixer at low revs, until a lump-free mixture is obtained. Apply with a roller or brush on the surfaces of SYNTECH POLYUREA SPRAY, within 24-48 hours of spreading the latter. A thorough sanding of the supports is recommended for any repairs and/or finishes. From 0.15 to 0.25 kg of SYNTYECH POLIUREA TOP COATING for each square metre of surface to be covered. Can 6.7 kg [A] - Can 3.3 kg [B] - Kit: 1 Can 6.7 kg [A] + 1 Can 3.3 kg [B]